Toastmaster MERB10B User Manual

READ AND SAVE THESE INSTRUCTIONS  
High-Speed Brewer  
1
ADDITIONAL IMPORTANT  
SAFEGUARDS  
WARNING: This appliance generates heat and escaping steam  
during use. Proper precautions must be taken to prevent the risk  
of burns, fires, or other injury to persons or damage to property.  
• All users of this appliance must read and understand this Use  
and Care Guide before operating or cleaning this appliance.  
• The cord to this appliance should be plugged into a 120V AC  
electrical outlet only.  
• Use water only in this appliance! Do not put any other liquids  
or food products in this appliance. Do not mix or add anything  
to the water placed in this appliance, except as instructed in the  
User Maintenance Instructions to clean the appliance.  
• DO NOT attempt to move an appliance containing hot liquids.  
Allow appliance to cool completely before moving.  
• Keep appliance at least 4 inches away from walls or other  
objects during operation. Do not place any objects on top of  
appliance while it is operating. Place the appliance on a surface  
that is resistant to heat.  
• If this appliance begins to malfunction during use, immediately  
unplug the cord. Do not use or attempt to repair the  
malfunctioning appliance.  
• If this appliance falls or accidentally becomes immersed in  
water or any other liquid, unplug it immediately. Do not reach  
into the water! Do not use this appliance after it has fallen  
into or has become immersed in water. Contact Consumer  
Service for examination and repair.  
• Do not leave this appliance unattended during use.  
• The appliance must be left to cool down sufficiently before  
adding more water to avoid splattering.  
• Always use fresh, cool water in your appliance. Warm water or  
other liquids, except as listed in the “Care and Cleaning”  
section, may cause damage to the appliance.  
• DO NOT put Carafe into a microwave.  
• DO NOT leave empty Carafe on Warming Plate when appliance  
is turned ON, as the Carafe may crack or become otherwise  
damaged.  
3
POLARIZED PLUG: This appliance has a polarized plug (one  
blade is wider than the other). To reduce the risk of electric shock,  
this plug is intended to fit into a polarized outlet only one way. If the  
plug does not fit fully in the outlet, reverse the plug. If it still does  
not fit, contact a qualified electrician. Do not attempt to modify the  
plug in any way.  
SHORT CORD INSTRUCTIONS: A short power-supply cord is  
provided to reduce the risk resulting from becoming entangled in  
or tripping over a longer cord. Do not use an extension cord with  
this product.  
ELECTRIC POWER: If the electrical circuit is overloaded with  
other appliances, your appliance may not operate properly. It  
should be operated on a separate electrical circuit from other  
appliances.  
CAUTION: To prevent plasticizers from migrating from the finish of  
the countertop or tabletop or other furniture, place NON-PLASTIC  
coasters or placemats between the appliance and the finish of the  
countertop or tabletop.  
Failure to do so may cause the finish to darken, permanent  
blemishes may occur or stains can appear.  
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC  
SHOCK, DO NOT REMOVE THE BOTTOM COVER. NO USER-  
SERVICEABLE PARTS INSIDE. REPAIR SHOULD BE DONE BY  
AUTHORIZED SERVICE PERSONNEL ONLY.  
4
Your product may vary slightly from illustration.  
Parts Identification  
Water Chamber Lid  
Water Fill Area  
Removable  
Filter  
(P/N 31186B)  
Water Chamber  
Shower Head  
Swing-Out  
Filter Holder  
(P/N 31187B)  
Carafe Lid  
(P/N 31189B)  
Glass Carafe  
w/Lid  
(P/N 31188B)  
Warming Plate  
Power Switch  
Warming Plate  
Switch  
Power  
Indicator Light  
Warming Plate  
Indicator Light  
FIGURE A  
FILL/BREW  
Control Dial  
Water  
Chamber Lid  
Before adding water set dial to “FILL”  
FIGURE B  
5
Coffee Maker Features  
and Benefits  
The one-time initial set-up of the coffee maker (see “Before Using  
Your Momentum Coffee Maker,page 7) prepares the coffee maker  
by filling the Water Chamber completely full of water and allowing  
time for the water to heat to proper brewing temperature. After this  
one-time set-up is completed, each time you brew a pot of coffee  
the cold water you pour into the coffee maker pushes out an equal  
amount of pre-heated hot water from the Water Chamber. The hot  
water flows over the coffee grounds and produces a fresh, hot pot  
of coffee. The cold water you just poured in remains in the Water  
Chamber where it is heated in preparation to brew the next pot!  
10-Cup Brewing Capacity - The coffee maker is designed to  
brew 6 to 10 cups of coffee at a time.  
Removable Filter - The Removable Filter pulls out for fast and  
easy cleaning and filling.  
Non-Stick Warming Plate - This feature allows you to keep  
your coffee hot after brewing. The non-stick coating prevents the  
Carafe from sticking to the surface of the Warming Plate.  
To avoid damaging the Carafe, the Warming Plate On Switch must  
be turned Off when the Carafe is empty or when the coffee maker  
is not in use.  
ON/OFF Power Switch- Allows you to turn off the power to the  
Water Chamber if the coffee maker will not be used for a few days.  
NOTE: The coffee maker is designed to remain plugged in with the  
Power Switch turned On except during those times when your  
coffee maker is emptied for transport or storage or during times  
when it will not be used for several days.  
If the coffee maker has been unplugged or the Power Switch turned  
Off for longer than a few hours it will take approximately 20 minutes  
after the unit is plugged back in and the Power Switch turned On to  
reheat the water supply to the proper temperature for brewing.  
If the coffee maker has not been used for 3 or more days, it is  
recommended that the Water Chamber be emptied and replaced  
with fresh water.  
6
Before Using Your  
Momentum Coffee Maker  
Before using your Momentum Coffee Maker for the first time, we  
suggest you become familiar with all of its parts. Read all  
instructions and cautions carefully.  
This initial set-up procedure prepares the coffee maker for use by  
filling the Water Chamber completely full of water and allowing  
time for the water to reach proper brewing temperature. This  
procedure is only required the first time the coffee maker has not  
been used, if your coffee maker has not been used for several  
days and has been emptied, or after the coffee maker has been  
drained for transport or long term storage (see “Draining Your  
Coffee Maker For Transport or Storage,page 10.)  
CAUTION: To avoid damage to the coffee maker, do not connect  
the power cord to a power outlet until the following steps have  
been completed.  
NOTE: The coffee maker will be heavy after the initial set-up steps  
are completed. For that reason it is recommended you place your  
coffee maker where you intend to use it before following the initial  
set-up procedure.  
1. Make sure the coffee maker is unplugged. Wash the Carafe,  
Carafe Lid and the Removable Filter in warm water and mild  
detergent. Rinse thoroughly then dry with a clean cloth. Place  
the Removable Filter in the Swing-Out Filter Holder.  
2. For this initial set-up, set the Control Dial to “Brew.”  
3. Fill the Carafe with fresh, cold water to the “10 cup” line.  
4. Slowly empty the water into the Water Fill Area on top of the  
coffee maker. Allow a few minutes for the water to drain into  
the Water Chamber.  
5. Fill the Carafe a second time with fresh, cold water to the “10  
cup” line.  
6. Slowly empty the water into the Water Fill Area on the top of  
the coffee maker. Allow a few minutes for the water to drain  
into the Water Chamber.  
7. Fill the Carafe a third (final) time with fresh, cold water to the  
“2 cup” line corresponding to the top of the metal band.  
8. Slowly empty the water into the Water Fill Area on top of the  
coffee maker and close the Water Chamber Lid.  
7
NOTE: Adding more water than the amount specified may  
cause water to flow from the Removable Filter. If this occurs,  
replace the Carafe under the Swing-Out Filter Holder or use a  
separate container to collect the excess water. Make sure all  
excess water has been collected and carafe has been  
emptied before moving on to the next step.  
9. Plug the power cord into a working 120 Volt AC power outlet  
and press the Power Switch. The Power Indicator Light will  
illuminate while appliance is On.  
NOTE: The coffee maker is designed to remain plugged in  
with the Power Switch turned On except during those times  
when your coffee maker is emptied for transport or storage or  
during times when it will not be used for several days.  
10. Wait 20 minutes to allow the water in the Water Chamber to  
reach the proper brewing temperature.  
You have completed the one-time set-up procedure and are ready  
to use your coffee maker to brew fresh, hot, delicious tasting coffee.  
For step-by-step instructions please read the “Brewing” section  
below.  
Brewing  
Make sure that you have completed the initial set-up before  
brewing.  
1. Set the Control Dial to “FILL.This setting prevents the water  
from entering the Water Chamber and allows time for the  
Carafe to be placed in position before starting the brew cycle.  
FIGURE B  
8
2. With the Removable Filter in position in the Swing-Out  
Filter Holder, place a #4 Melitta Cone Filter into the  
Removable Filter.  
3. Add the appropriate amount of ground coffee to the filter (See  
Suggested Coffee Measurement Chart below.) Move the  
Swing-Out Filter Holder in position on the coffee maker, it will  
snap when it is secure.  
WARNING: To avoid risk of personal injury or damage to  
property, be sure that the Swing-Out Filter Holder is securely  
in place. Failure to secure the Swing-Out Filter Holder may  
result in hot water overflowing and spilling out of the machine.  
Suggested Coffee Measurement Chart  
For best results, use a level tablespoon for ground coffee  
measurement. Make sure you use medium grind coffee for  
perfect brew.  
Number of Cups  
Level Tablespoons  
10  
8
6
7.5  
6
4.5  
1 cup = 5-oz. brewed coffee  
Use more or less coffee to adjust to your taste.  
4. Fill the Carafe with 6 to 10 cups of cold water.  
NOTE: The coffee maker is designed to brew 6 to 10 cups of  
coffee at a time. Attempting to brew less than 6 cups may  
provide unsatisfactory results.  
5. Carefully pour the water into the Water Fill Area on top of the  
coffee maker.  
6. Place the Carafe on the Warming Plate.  
7. To start the brew cycle, set the Control Dial to “BREW.”  
8. Press the Warming Plate Switch to On. The Warming Plate  
Indicator Light will illuminate to indicate that the Warming  
Plate is on.  
NOTE: To avoid damaging the Carafe, the Warming Plate  
Switch must be turned Off when the Carafe is empty or when  
the coffee maker is not in use.  
9. When the brew cycle is complete set the Control Dial to “FILL”  
to prepare machine for the next pot of coffee. You can now  
enjoy your freshly brewed pot of delicious coffee.  
9
10. After allowing the coffee grounds to cool, carefully remove  
and discard the used coffee grounds and filter.  
WARNING: Brewed coffee and grounds, both in the  
Removable Filter and Carafe are very hot! Handle with care to  
avoid scalding. If Removable Filter overflows, or if the  
Removable Filter fails to drain the coffee into the Carafe  
during the brew cycle, do not open or handle the Swing-Out  
Filter Holder and Removable Filter. Turn the Control Dial to  
“FILL, unplug the coffee maker and wait for the contents to  
cool before opening.  
Draining Your Coffee Maker for  
Transport or Storage  
The Water Chamber in your coffee maker should be emptied  
whenever the coffee maker will be transported, or stored for  
extended lengths of time.  
WARNING: The coffee maker is very heavy. Use caution when  
draining the chamber.  
1. Turn the Power Switch to Off and unplug the coffee maker  
power cord from the power outlet.  
CAUTION: TO PREVENT INJURY DO NOT ATTEMPT TO  
DRAIN THE UNIT UNTIL THE WATER IN THE WATER  
CHAMBER HAS COOLED. THIS WILL TAKE SEVERAL  
HOURS.  
NOTE: To shorten the length of time required for the water to  
cool, the hot water in the Water Chamber can be flushed out  
and replaced with cold water. To do this:  
a. Turn the Power Switch Off and unplug the unit from the  
power outlet.  
b. Using 10 cups of cold water follow the instructions for  
“Brewing” section. While performing this procedure do  
not use a filter or coffee grounds.  
c. Repeat the 10 cup brewing process at least three times  
to ensure that the hot water in the chamber has been  
replaced with cold water.  
2. Turn the Control Dial to “FILL.”  
3. Remove the Removable Filter and Swing-Out Filter Holder.  
10  
4. Grasp the back of the coffee maker and tip the unit forward  
over a sink at a 45 degree angle until the water begins to flow  
out of the Shower Head.  
5. Slowly top the coffee maker to a 90 degree angle, hold until  
the flow of water stops.  
NOTE: To ensure that your coffee maker will function properly  
in the future do not tip the coffee maker beyond 90˚.The small  
amount of water remaining in the coffee maker following this  
procedure will evaporate in a few days time.  
Care and Cleaning  
Routine Cleaning  
The Carafe, Carafe Lid and the Removable Filter should be rinsed  
with water after each use.  
Top rack dishwasher safe parts: the Carafe and Lid, the  
Removable Filter and the Swing-Out Filter Holder.  
A small amount of dishwashing liquid and water will remove most  
fingerprints, grease, dirt and grime.  
Occasionally, window cleaners, vinegar and water solutions,  
standard non-abrasive kitchen cleaning fluids, or commercially  
available cleaning products for stainless steel surfaces can be  
used. After cleaning, use a soft, dry cloth to dry and buff the  
surface to a brilliant shine.  
Descaling  
We recommend that you descale your coffee maker once a month  
because mineral deposits can form a coating in the coffee maker,  
causing slower brewing time and possibly an off flavor in the  
coffee. Use a cleaner recommended for coffee makers or the  
solution described below. To descale your unit:  
1. Turn the Power Switch to “Off”. Unplug the coffee maker  
power cord from the power outlet.  
2. Place the Swing-Out Filter Holder in position on the coffee  
maker.  
3. Place the Carafe on the Warming Plate.  
4. Slowly pour 1 quart (32 fluid ounces) of undiluted white  
household vinegar into the top of the coffee maker.  
11  
NOTE: As the vinegar is poured in, hot water will be pushed  
from the Water Chamber and flow through the Removable  
Filter into the Carafe.  
5. When the flow of water stops, empty the Carafe then replace  
it on the Warming Plate.  
6. Wait 2 hours before proceeding. This will allow the vinegar  
time to break down the lime and mineral deposits.  
7. After 2 hours, the vinegar may be rinsed from the coffee  
maker.  
a. Using 10 cups of cold water follow the instructions for  
“Brewing,page 8. While performing this procedure do  
not use a filter or coffee grounds.  
b. Repeat the 10 cup brewing process at least eight times  
to ensure that the vinegar in the Water Chamber has  
been replaced with cold water.  
NOTE: An easy way to determine if all the vinegar has been  
rinsed out is to sprinkle a small amount of baking soda into  
the water in the Carafe after it has completed the brewing  
cycle. The baking soda will react with the vinegar. A gentle  
fizzing indicates that there is still vinegar in the water and the  
procedure should be repeated. If there is no reaction then it  
means that all of the vinegar has been rinsed clean.  
Cleaning the Carafe  
Hard water can leave a whitish mineral deposit inside the Carafe.  
Coffee can discolor these deposits, sometimes leaving a brownish  
stain. To remove these stains, follow these simple steps:  
1. Use a solution of equal parts: white household vinegar and  
hot water.  
2. Let solution stand in Carafe for about 20 minutes and then  
discard.  
3. Wash and rinse the Carafe thoroughly using a soft cloth. Do  
not use harsh abrasive cleaners. These may cause scratches  
which can lead to breakage.  
NEVER IMMERSE THE COFFEE MAKER IN WATER OR  
OTHER LIQUIDS.  
12  
IMPORTANT NOTICE  
If any parts are missing or defective,  
DO NOT return this product.  
Please call our Customer Service Department for assistance.  
800-233-9054 Monday - Friday 9:00 am - 5:00 pm CST  
Thank You  
LIMITED ONE-YEAR WARRANTY  
Warranty Coverage: This product is warranted to be free from defects in  
materials or workmanship for a period of one (1) year from the original  
purchase date. This product warranty is extended only to the original  
consumer purchaser of the product and is not transferable. For a period of  
one (1) year from the date of original purchase of the product, our Repair  
Center will, at its option, either (1) repair the product or (2) replace the  
product with a reconditioned comparable model. These remedies are the  
purchaser’s exclusive remedies under this warranty.  
Warranty Service: To obtain warranty service, you must call our warranty  
service number at 1-800-233-9054 for return instructions on how to deliver  
the product, in either the original packaging or packaging affording an equal  
degree of protection to the Repair Center specified below. You must  
enclose a copy of your sales receipt or other proof of purchase to  
demonstrate eligibility for warranty coverage.  
To return appliance, ship to: To contact us, please write to, call, or email:  
Attn: Repair Center  
708 South Missouri Street  
Macon, MO 63552 USA  
Consumer Relations Department  
P.O. Box 7366  
Columbia, MO 65205-7366 USA  
1-800-233-9054  
What Is Not Covered: This warranty does not cover damage resulting  
from misuse, accident, commercial use, improper service or any other  
damage caused by anything other than defects in material or workmanship  
during ordinary consumer use. This warranty is invalid if the serial number  
has been altered or removed from the product. This warranty is valid only  
in the United States and Canada.  
LIMITATION ON DAMAGES: THERE SHALL BE NO LIABILITY FOR ANY  
INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY  
EXPRESS OR IMPLIED WARRANTY OR CONDITION ON THIS PRODUCT.  
13  
DURATION OF IMPLIED WARRANTIES: EXCEPT TO THE EXTENT  
PROHIBITED BY APPLICABLE LAW, ALL IMPLIED WARRANTIES AND  
CONDITIONS, INCLUDING, WITHOUT LIMITATION, IMPLIED  
WARRANTIES AND CONDITIONS OF MERCHANTABILITY AND  
FITNESS FOR A PARTICULAR PURPOSE OR USE ON THIS PRODUCT  
ARE LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY.  
Some jurisdictions do not allow the exclusion or limitation of incidental or  
consequential damages, or allow limitations on how long an implied  
warranty lasts, so the above limitations or exclusions may not apply to you.  
This warranty gives you specific legal rights and you may have other rights  
under the laws of your jurisdiction.  
For more information on our products, visit our website:  
© 2005 Maxim-Toastmaster, Inc.  
All Rights Reserved  
P/N 61643  
Printed in China  
14  

Ultra Products 96500 User Manual
Toshiba IK 528A User Manual
Sprint Nextel Sprint PCS Vision Smart Device PPC 6700 User Manual
Sony PDW F75 User Manual
Sony Net MD Walkman MZ N1 User Manual
Seagate FreeAgent Go ST903203FAA2E1 RK User Manual
Samsung Computer Drive HX M640UAY User Manual
Philips HD7826 User Manual
Nokia N6270 User Manual
Nokia N81 3 User Manual